[NCLUG] cd writer

[Daniel Miles]

When it crashes it prints to the screen:
modproSCSI subsystem driver Revision: 1.00
behda: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0,
lun 0 0x12 00 00 00 ff 00

...maybe that helps somebody?

On Tue, 2003-11-25 at 11:35, Daniel Miles wrote:
> Thanks for the attempt, but it didn't work. I recompiled the kernel with
> ide-cd as a module instead of simply being built straight in... I booted
> the system with append="hda=ide-scsi" in my lilo.conf file, unloaded
> ide-cd and loaded ide-scsi. The result was the same, total system
> freeze.
> 
> On Mon, 2003-11-24 at 15:06, Kevin Fenzi wrote:
> > -----BEGIN PGP SIGNED MESSAGE-----
> > Hash: SHA1
> > 
> > >>>>> "Daniel" == Daniel Miles <milesd at cs.colostate.edu> writes:
> > 
> > Daniel> I have a Dell Inspiron 5100 notebook with a cd writer in
> > Daniel> it. The writer, for some strange reason, is on /dev/hda... So,
> > Daniel> in my lilo.conf file, I have append="hda=ide-scsi".
> > 
> > Daniel> I have the ide-scsi driver compiled as a module but when I
> > Daniel> insert that module, the system freezes and I have to hold down
> > Daniel> the power button for 5 seconds to turn it off... When I
> > Daniel> *don't* pass that info the the kernel and I just use the
> > Daniel> device as an ide device, it works fine (but not as a
> > Daniel> burner). This is a bummer because I'd really like to use the
> > Daniel> burner.
> > 
> > Daniel> There are no error logs that I can find (though I'm hardly an
> > Daniel> expert at finding error logs if you think there might be
> > Daniel> something somewhere) and the system just hangs.
> > 
> > Daniel> This happens on 2.2.19, 2.4.21 and 2.4.22 and it seems to
> > Daniel> happen regaurdless of weather or not I compile the ide-scsi
> > Daniel> driver as a module or not.
> > 
> > Did you build 'ide-cd' as a module?
> > You can't have both ide-cd and ide-scsi at the same time. 
> > It sounds like you might need to make ide-cd a module so it can be
> > unloaded before you load the ide-scsi one. 
> > 
> > Daniel> The strange thing about it was that it worked on 2.2.19 when I
> > Daniel> installed the (debian) system but it does not work now, even
> > Daniel> though I have made no changes to that kernel.
> > 
> > Try unloading ide-cd?
> > 
> > Daniel> Ok, that's all the information I can think to suppply. Thanks
> > Daniel> for giving this a shot. :)
> > 
> > Hope that helps... 
> > 
> > kevin
> > -----BEGIN PGP SIGNATURE-----
> > Version: GnuPG v1.2.2 (GNU/Linux)
> > Comment: Processed by Mailcrypt 3.5.8 <http://mailcrypt.sourceforge.net/>
> > 
> > iD8DBQE/woDy3imCezTjY0ERAhjfAJwLwn4EvNlGRMyc7KVRx8O3Q3nXXgCfQ9m9
> > dNb7Aov+D2FvSSWdqx8ubgQ=
> > =wkVD
> > -----END PGP SIGNATURE-----
> > _______________________________________________
> > NCLUG mailing list       NCLUG at nclug.org
> > 
> > To unsubscribe, subscribe, or modify 
> > your settings, go to: 
> > http://www.nclug.org/mailman/listinfo/nclug
> 
> _______________________________________________
> NCLUG mailing list       NCLUG at nclug.org
> 
> To unsubscribe, subscribe, or modify 
> your settings, go to: 
> http://www.nclug.org/mailman/listinfo/nclug